Install the app
How to install the app on iOS

Follow along with the video below to see how to install our site as a web app on your home screen.

Note: This feature may not be available in some browsers.

EVOL How are my settings?

Madeintheuk

HAM Sniper
469
1,150
Washington Depot, CT
HAM Points
2,441.00
Country flag
Hi guys! I purchased my evol mini used, and to this point, I haven’t played with anything.
My biggest qualm with this gun, is the cocking effort. It takes some muscle to cock. If it was a 30cal, I’d understand, but for a 27fpe 22cal, I’m not too sure it’s normal.

My reg looks to be around 1900psi

1A3B804B-6E0F-4D63-8570-290C983AE9D4.webp

I removed it from the stock with plans to do some adjustments to hammer, but it looks S though the adjuster is out pretty far already

B3907EDB-B05A-41AE-8C12-B4E35A0CF603.webp4B3726A1-91CF-48A0-B78A-F12D4FF4C9AB.webp

So I dare play with it until someone on here steers me the right direction.

I ran it over the chrony, and I’m shooting hades at 890fps with a spread of 3.5 which I consider to be a decent tune. I have noticed others have had lower reg pressures with similar speeds though, and no real complaining about cocking effort. Am I just being whiny? Am I too used to the ease of my FX guns? In fact EVERY other high end pcp I’ve owned has had lighter cocking than this. I can’t be the only one can I?

Help!!
 
I've had multiple FX guns to compare to my EVOL and ill take the short throw stout cocking over FX anything every day of the week. To me the tune looks good, I bet 18.13s would be the better match though. Is there something more you are wanting out of the tune? Less power more shots? The hammer spring is backed off quite far, too much farther and it might get difficult to get it back in the chassis.

The EVOL design is very simple. More cocking levers added to reduce cocking effort equals more points of failure. Which is exactly the problem I had with my easy cocking FX guns.
 
I've had multiple FX guns to compare to my EVOL and ill take the short throw stout cocking over FX anything every day of the week. To me the tune looks good, I bet 18.13s would be the better match though. Is there something more you are wanting out of the tune? Less power more shots? The hammer spring is backed off quite far, too much farther and it might get difficult to get it back in the chassis.

The EVOL design is very simple. More cocking levers added to reduce cocking effort equals more points of failure. Which is exactly the problem I had with my easy cocking FX guns.
I completely disagree with your FX comments. I’ve had zero issues with any of my FX cocking levers and “failure points”.
that being said, I’m not really looking for anything different. Moreso I’m looking to make sure others have noticed, and that it is considered normal for the rifle. I’m not unhappy with how it shoots, in fact, I’m very happy with accuracy and power. I just want to make sure it’s not overspringed for the reg pressure I’m running, and on the verge of something breaking.
 
The cocking is harder on the Evol compared to other guns I agree but is just the last part. Nothing to worry about. These guns aren't delicate. You'd have to do alot to really damage one lol. Mine is similar. 2000psi~ on the reg with tune at 885fps with 16gr. Mine maxes at 925fps at this speed. Ideally I think I'm going to switch to the JTS 18gr as they seem very consistent compared to other pellets. Those would probably run 850ish and would bump it up to 865fps. But yeah nothing to worry about on anything being damaged. Would be interesting to see your max fps at the reg setting to see how close it is to mine.
 
I completely disagree with your FX comments. I’ve had zero issues with any of my FX cocking levers and “failure points”.
that being said, I’m not really looking for anything different. Moreso I’m looking to make sure others have noticed, and that it is considered normal for the rifle. I’m not unhappy with how it shoots, in fact, I’m very happy with accuracy and power. I just want to make sure it’s not overspringed for the reg pressure I’m running, and on the verge of something breaking.
Both my wildcat bt and maverick left me stranded on hunts because a pin fell out of the linkage in the dirt, a pin that is never supposed to come out.

I dont hate FX, they have strong points was just using them to compare the two styles. One being easier to cock by way of leverage and the other less moving parts for added reliability but stiffer cocking.

Like dairyboy said your tune and performance looks on par, wouldn't worry at all about too much hammer for reg pressure. Personally I have found on my EVOL 15" .22 that it has a wide range of adjustment IF your not always looking for single digit ES. My current tune is 2300 psi on the reg shooting H&N 23 grain slugs at 930 fps for 4 mags with single digit ES...then to shoot 18.13 pellets, back HS off 1.25 turns which gives me about 890 fps for around 7 mags. Most of the time the ES stays at 10 or less on the pellet tune but at times(usually with temp swings) goes to 15 or so. For hunting out 75 yards with pellets, that never matters. For target shooting might be different.
 
Your setup is typical of how Minis leave the factory. Cocking on EVOLS is stout when compared to some others but there are valid reasons behind the design.

There are always compromises when designing anything. The key is to identify the key features and/or behaviors and assign them priorities from high to low, once this has been done the design can be addressed.

In the case of the EVOL the priorities are:

Reliability - Cocking system is robust and uses high strength steel and aluminum, appropriate parts are heat treated/stress relieved for wear resistance and strength. Pins are sized not to break or elongate holes during high stress operation.

Efficiency - FPE per CuIn of air used - The stiff, non preloaded spring resists air wasting hammer bounce. Due to the very high spring rate it cannot be significantly re-compressed when the hammer returns rearward during the shot cycle. Also, the valve and porting is large to allow the charge to enter the valve and transfer port as fast as possible and close rapidly, this reduces thermal loss and provides high break away energy for pellet which is where significant amount of the impulse energy is consumed.

Deep magazine - To accommodate Polymag and heavier slugs in all calibers. A deeper magazine requires a longer bolt throw which increases the dead space before the lever takes up the spring and begins to compress it, leaving the last few degrees of the lever throw to do all the work.

Minimum overall length of the receiver - Shorter receiver less weight and more barrel for a given length.


Cocking effort of a 30 is not much more than a Mini because the bore area and the barrel length are doing all the work.

Reducing the cockling effort has been on our radar for some time and we have been developing upgrades that will reduce the cocking effort by 40% on a standard EVOL. The challenge has been not to reduce the efficiency of the system and has been exceeding difficult because the systems has a very level of efficiency to begin with.

The new system will be backwards compatible with all EVOLs. The kit will contain a new Adjuster with ball detent, and a spring, guide rod, striker assembly.


Tom
 
Your setup is typical of how Minis leave the factory. Cocking on EVOLS is stout when compared to some others but there are valid reasons behind the design.

There are always compromises when designing anything. The key is to identify the key features and/or behaviors and assign them priorities from high to low, once this has been done the design can be addressed.

In the case of the EVOL the priorities are:

Reliability - Cocking system is robust and uses high strength steel and aluminum, appropriate parts are heat treated/stress relieved for wear resistance and strength. Pins are sized not to break or elongate holes during high stress operation.

Efficiency - FPE per CuIn of air used - The stiff, non preloaded spring resists air wasting hammer bounce. Due to the very high spring rate it cannot be significantly re-compressed when the hammer returns rearward during the shot cycle. Also, the valve and porting is large to allow the charge to enter the valve and transfer port as fast as possible and close rapidly, this reduces thermal loss and provides high break away energy for pellet which is where significant amount of the impulse energy is consumed.

Deep magazine - To accommodate Polymag and heavier slugs in all calibers. A deeper magazine requires a longer bolt throw which increases the dead space before the lever takes up the spring and begins to compress it, leaving the last few degrees of the lever throw to do all the work.

Minimum overall length of the receiver - Shorter receiver less weight and more barrel for a given length.


Cocking effort of a 30 is not much more than a Mini because the bore area and the barrel length are doing all the work.

Reducing the cockling effort has been on our radar for some time and we have been developing upgrades that will reduce the cocking effort by 40% on a standard EVOL. The challenge has been not to reduce the efficiency of the system and has been exceeding difficult because the systems has a very level of efficiency to begin with.

The new system will be backwards compatible with all EVOLs. The kit will contain a new Adjuster with ball detent, and a spring, guide rod, striker assembly.


Tom
Thank you for such a detailed response. I know the gun was built rugged, and that’s the main reason I bought one. To be clear, I am not in any way disappointed with the rifle or any part of it. Hopefully you and everyone else that read my post didn’t come to that conclusion. Buying a used gun is always a little scary. You never know what the previous owner did, and this being my first evol, i had nothing to compare it to. I wanted to make sure that it was where it was supposed to be, and will continue to give me years of uninterrupted use.
thanks again Tom! You make a superior gun in every way! The fact that you’re following up with new tech that will be backwards compatible us even more awesome. I’m super excited to see What the future holds for your company and your products!
 
Hi guys! I purchased my evol mini used, and to this point, I haven’t played with anything.
My biggest qualm with this gun, is the cocking effort. It takes some muscle to cock. If it was a 30cal, I’d understand, but for a 27fpe 22cal, I’m not too sure it’s normal.
Like Tom mentioned, there are Pros and Cons. Think how much stronger your arm will be now. :)
 

Create an account or login to comment

You must be a member in order to leave a comment

Create FREE account

Create a FREE account on our community. It's easy!

Log in

Already have an account? Log in here.

Trending in this forum

Back
Top