Install the app
How to install the app on iOS

Follow along with the video below to see how to install our site as a web app on your home screen.

Note: This feature may not be available in some browsers.

HM1000X Tuning and modifications

Woogie_man

HAM Wizard
1,252
3,574
Fargo, ND
Airguns of Arizona - 10% discount
Country flag
Well here I go again on another journey.......

I have my HM1000X from Martin and I have been playing with it for a week now. I have come to the conclusion that the 217 JSB KnockOut slugs shoot great at 970 fps. I have a few other slugs to play with, as well as the slugs my buddy is making me from his Corbin Press. I am loving the MPA chassis for this rifle, as the fit and finish is top level as well is the adjustability. So far the rifle has been great, and I am hoping to see how the rifle will shoot on sunday at a local match.

So I am looking at different modifications or upgrades to the rifle. I have a muzzle break on the rifle right now, as well as an Eagle Vision tunable muzzle break. I am planning on trying a few different cans on the end to see if they make any different. As I was looking around instagram I saw a post about a plenum for the rifle that helps with shooting heavier slugs. And this got me to thinking about other modifications and or upgrades that can be done with the rifle.

Aside from upping the bottle to a 700cc or anything like that I am not sure what else to do to the rifle.

I have 20 different slug designs and weights of slugs. Hoping to hit the range tomorrow to get some more velocities as well as some groupings at 50, 75, and 100 yards.

What else do you guys want to see or are questioning about the rifle?
 
Last edited:
Well I did a little over 2 hours of shooting with the rifle at the range. Tested with the muzzle break, the Eagle vision muzzle, an Impulse Air 1350, and the bare muzzle. There were a few glimpses of greatness, but sadly they were not repeatable. At the end of the session I wound back on the JSB KnockOuts in 217, though I did bump the speed up a little and was able to tighten up the groups a little bit. Was shooting at a 10m airgun target at distances of 50, 75, and 100 yards. The last target page I loaded a magazine with 12 rounds and shot 3 at 50 to confirm zero, moved target to 75 yards...adjusted scope and shot again, moved to 100 yards.....adjusted scope and shot again. This confirmed my Strelok numbers and showed that the rifle was true for a match on Sunday.

I am going to grab my phone and upload some pictures of the targets and my notes. Be aware I was adjusting the velocity as well as trying different slugs and combinations to see if anything showed promise.

20240501_191848.webp20240501_191917.webp20240501_191930.webp20240501_191949.webp
 

Attachments

  • 20240501_192015.webp
    20240501_192015.webp
    431.9 KB · Views: 7
  • 20240501_192025.webp
    20240501_192025.webp
    429.3 KB · Views: 6
  • 20240501_192034.webp
    20240501_192034.webp
    417.5 KB · Views: 5
Settle on one projectile/velocity setting, then practice, practice, practice. The gun is not going to make up for bad marksmanship practices.
 
The plan was to take the rifle to an NRL22 match on Sunday, but with the rain we have been getting up here the range is far to wet. So we are pushing back the match for another week. This will give me more time to practice with the rifle overall.
 
Well here I go again on another journey.......

I have my HM1000X from Martin and I have been playing with it for a week now. I have come to the conclusion that the 217 JSB KnockOut slugs shoot great at 970 fps. I have a few other slugs to play with, as well as the slugs my buddy is making me from his Corbin Press. I am loving the MPA chassis for this rifle, as the fit and finish is top level as well is the adjustability. So far the rifle has been great, and I am hoping to see how the rifle will shoot on sunday at a local match.

So I am looking at different modifications or upgrades to the rifle. I have a muzzle break on the rifle right now, as well as an Eagle Vision tunable muzzle break. I am planning on trying a few different cans on the end to see if they make any different. As I was looking around instagram I saw a post about a plenum for the rifle that helps with shooting heavier slugs. And this got me to thinking about other modifications and or upgrades that can be done with the rifle.

Aside from upping the bottle to a 700cc or anything like that I am not sure what else to do to the rifle.

I have 20 different slug designs and weights of slugs. Hoping to hit the range tomorrow to get some more velocities as well as some groupings at 50, 75, and 100 yards.

What else do you guys want to see or are questioning about the rifle?
What do you find is the heaviest slug you can push with accuracy? And what grain slug do you get the most accuracy out of? Martin is gonna build me a .22 cal action and I'm going to put it in a mpa chassis just like you did. He said I could get a slug tune for either 23 - 25 - 27 grain. Not sure if it will push heavier slugs with extreme accuracy. I used to be all caught up on heavy slugs but I'm starting to realize all that matters is accuracy !
 
Match over and gun is repaired.....the wind was my worst enemy on Sunday! The rifle performed well, though it could have been better. I some how bent the inner probe before the match, not sure when and how this effected the shots.

1st stage was able to put 9 of 12 shots on a plate at 100 yards off of a tank trap obstacle, and the group was around the size of a half dollar!

After getting home I replied the probe and installed an extended plenum. Hoping to get out shooting soon and do some more testing. The heaviest I have shot is a 40 grain, and those go slow. 😆 I am hoping with the plenum I can up the grains a bit to help with the wind issues.
 
Just did some simple testing here in the house with the loading and shooting of different slugs. And they all worked great and they all had some speed to them! SO......... I am hoping to be able to push a heavier slug to help buck the wind better.

Taking the rifle to the indoor tubes tomorrow to get some testing done. Will be back with numbers and groups tomorrow.
 
Just did some simple testing here in the house with the loading and shooting of different slugs. And they all worked great and they all had some speed to them! SO......... I am hoping to be able to push a heavier slug to help buck the wind better.

Taking the rifle to the indoor tubes tomorrow to get some testing done. Will be back with numbers and groups tomorrow.
Heavier you say...so like in the 28 to 34 grain range? You meant earlier you had damaged pellet loading probe? I'm convinced I have a small bur on the end of mine on the S510, lots of pellets will bind alittle getting loaded. The crosman 19gr heavies will actually stick to the probe and pull partially back out with it (bad times!) I'm dying to debur and polish it but nowhere nears the room I need to get in there without stripping it down, and that's not happening till I need to if it ever leaks.
 
Match over and gun is repaired.....the wind was my worst enemy on Sunday! The rifle performed well, though it could have been better. I some how bent the inner probe before the match, not sure when and how this effected the shots.

1st stage was able to put 9 of 12 shots on a plate at 100 yards off of a tank trap obstacle, and the group was around the size of a half dollar!

After getting home I replied the probe and installed an extended plenum. Hoping to get out shooting soon and do some more testing. The heaviest I have shot is a 40 grain, and those go slow. 😆 I am hoping with the plenum I can up the grains a bit to help with the wind issues.
I don't know how you could have bent the probe, but if you are using slugs too large in diameter and they are hard to chamber, you might consider getting some that are a little smaller in diameter. You'll get higher velocity too.
 
That's the same thing Martin said. There were a few slugs that were really tight.. was able to fix the issue so no worries
I just talked to martin about my .22 action and he said in stock form he could tune it to shoot 30 grain slugs at 970 fps. By just raising the regulator pressure and tweaking the hammer spring. With that external plenum you should be able to push at least 34 grain slugs at very high fps. Have you tried it yet With the external plenum and heavier slugs? I'd be very interested in knowing if it can push 34-40 grains up to 970 fps. And can the magazine even fit 40 grain slugs?? I didn't think of that till just now.
 
I will be shooting this afternoon. I will let you know what happens. I have some Javelin V2 34 grain slugs I can try. Then when I get home I can try some of the 40s as well
 
Last edited:
Ok guys........ here are the results of 2 hours of shooting at the range today. The shooting tubes are indoors, a local underground range that is 2 blocks from my work. It was a moist 68* and rainy outside, so that made the range a bit chilly but mostly dry. I started shooting at 25 yards to make sure things were working ok since I added the plenum extension, and having had to disassemble the rifle and bend the inner probe back. After I made sure things were shooting ok I started with the testing.

Each group is 5 shots, unless the chronograph didn't pick up 5 shots and I shot more to get a consistent numbers. Where you are seeing the +1 turn and then just +1 etc this is the hammer spring adjuster on the rear. I marked the adjuster just like I showed when I was playing with the AAA HPS30. This helps in keeping things consistent and easy to index. I REALLY wish companies would add hash marks around the outside of the adjuster to help in tuning. Would be a great little addition that wouldn't add to much to the overall cost of the rifle.

I was doing rough adjustments on the rifle to see what I was able to accomplish. The 25 grain range of slugs shot great and I could feel a difference in the shot cycle when shooting. There didn't seem to be as much stress on the rifle and the valving sounded smoother while cycling. I did shoot some 30 and 34 grain Javelin V2 slugs just to see what speeds I can get. I was able to get close to 900 fps with the 34 grain slugs and there was still more hammer tension I could add. Now I didn't adjust the regulator as I didn't have any of my equipment to adjust and don't want to adjust just yet. Saying that the felt recoil was quite a bit more when going with the 34 grain slugs. You could really feel these slugs when shooting and I was honestly shocked. I have no doubt that the gun will shoot them but the effect it will have on the shot count is unknown at this point.

Speaking of shot count........ The rifle fills to a max of 250 bar. I was able to shoot 2 targets, so 10 shots with only 10 bar of pressure lost. I am looking at getting a digital gauge for the rifle so I can see exactly what the efficiency of the rifle is. But being as my main focus is to use this rifle for NRL22 matches, having 12 full powered shots I am ok with the shot count at this point.

Over all I am looking at the Corbin .218 X Hollow Point, this is one of their newer products, and they were shooting shockingly good. At the end of the session I was shooting from 25, 50, 75, and 100 yards at a new bull for each distance. And you can see the dispersion but it was consistent and I can't wait to get the gun out and hopefully shooting a few gophers and bunnies with it. My shooting buddy and I have been talking with Corbin and will be working on getting videos and pictures while using them ;) The other slugs I am going to play more with are the H&N Slug HP that are 25 grains as well as the JSB KnockOut in the 25.39 grains, both in the .217 size. This is what kind of confused me and frustrated me..... is the rifle was shooting both of these sizes very well!

I did start the 50 yard page with just a naked barrel. There was the adapter for the DonnyFL Ryu quick release adapter on the end, but no muzzle break or anything like that. I wanted to see what the rifle would do with a bare barrel and then add a moderator or muzzle break to see, if any, difference these will have on the groups. I do have a DonnyFL Ryu and Yokozuna, and Impulse Air 1350, a muzzle break that I purchased from South Africa, and a tunable muzzle break from Eagle Vision. I will get a group picture of them all so we can all see what is going on.

Over all I left the range with one heck of a headache, and ready to get home and shower. Being as I went from my job right to the range I was gross and slimy from a rough day at work. I am going to do more work and testing to get these groups as small as possible. If there is anything you guys want to see or want tested just let me know. I will see what I can do and give them a shot.

One thing I did notice is that the H&N slugs I had previously had, and finished off at the range, had a weird waxy lubricant on them. But the tin I opened up during this shooting session the slugs looked clean and didn't have that waxy looking appearance to them? I am also debating on trying some of the JSB KnockOuts in the V2. Not sure there will be any difference between the flat walled V1 and the flared base of the V2.



20240521_165125.jpg20240521_165131.jpg
 
Ok guys........ here are the results of 2 hours of shooting at the range today. The shooting tubes are indoors, a local underground range that is 2 blocks from my work. It was a moist 68* and rainy outside, so that made the range a bit chilly but mostly dry. I started shooting at 25 yards to make sure things were working ok since I added the plenum extension, and having had to disassemble the rifle and bend the inner probe back. After I made sure things were shooting ok I started with the testing.

Each group is 5 shots, unless the chronograph didn't pick up 5 shots and I shot more to get a consistent numbers. Where you are seeing the +1 turn and then just +1 etc this is the hammer spring adjuster on the rear. I marked the adjuster just like I showed when I was playing with the AAA HPS30. This helps in keeping things consistent and easy to index. I REALLY wish companies would add hash marks around the outside of the adjuster to help in tuning. Would be a great little addition that wouldn't add to much to the overall cost of the rifle.

I was doing rough adjustments on the rifle to see what I was able to accomplish. The 25 grain range of slugs shot great and I could feel a difference in the shot cycle when shooting. There didn't seem to be as much stress on the rifle and the valving sounded smoother while cycling. I did shoot some 30 and 34 grain Javelin V2 slugs just to see what speeds I can get. I was able to get close to 900 fps with the 34 grain slugs and there was still more hammer tension I could add. Now I didn't adjust the regulator as I didn't have any of my equipment to adjust and don't want to adjust just yet. Saying that the felt recoil was quite a bit more when going with the 34 grain slugs. You could really feel these slugs when shooting and I was honestly shocked. I have no doubt that the gun will shoot them but the effect it will have on the shot count is unknown at this point.

Speaking of shot count........ The rifle fills to a max of 250 bar. I was able to shoot 2 targets, so 10 shots with only 10 bar of pressure lost. I am looking at getting a digital gauge for the rifle so I can see exactly what the efficiency of the rifle is. But being as my main focus is to use this rifle for NRL22 matches, having 12 full powered shots I am ok with the shot count at this point.

Over all I am looking at the Corbin .218 X Hollow Point, this is one of their newer products, and they were shooting shockingly good. At the end of the session I was shooting from 25, 50, 75, and 100 yards at a new bull for each distance. And you can see the dispersion but it was consistent and I can't wait to get the gun out and hopefully shooting a few gophers and bunnies with it. My shooting buddy and I have been talking with Corbin and will be working on getting videos and pictures while using them ;) The other slugs I am going to play more with are the H&N Slug HP that are 25 grains as well as the JSB KnockOut in the 25.39 grains, both in the .217 size. This is what kind of confused me and frustrated me..... is the rifle was shooting both of these sizes very well!

I did start the 50 yard page with just a naked barrel. There was the adapter for the DonnyFL Ryu quick release adapter on the end, but no muzzle break or anything like that. I wanted to see what the rifle would do with a bare barrel and then add a moderator or muzzle break to see, if any, difference these will have on the groups. I do have a DonnyFL Ryu and Yokozuna, and Impulse Air 1350, a muzzle break that I purchased from South Africa, and a tunable muzzle break from Eagle Vision. I will get a group picture of them all so we can all see what is going on.

Over all I left the range with one heck of a headache, and ready to get home and shower. Being as I went from my job right to the range I was gross and slimy from a rough day at work. I am going to do more work and testing to get these groups as small as possible. If there is anything you guys want to see or want tested just let me know. I will see what I can do and give them a shot.

One thing I did notice is that the H&N slugs I had previously had, and finished off at the range, had a weird waxy lubricant on them. But the tin I opened up during this shooting session the slugs looked clean and didn't have that waxy looking appearance to them? I am also debating on trying some of the JSB KnockOuts in the V2. Not sure there will be any difference between the flat walled V1 and the flared base of the V2.

Ok guys........ here are the results of 2 hours of shooting at the range today. The shooting tubes are indoors, a local underground range that is 2 blocks from my work. It was a moist 68* and rainy outside, so that made the range a bit chilly but mostly dry. I started shooting at 25 yards to make sure things were working ok since I added the plenum extension, and having had to disassemble the rifle and bend the inner probe back. After I made sure things were shooting ok I started with the testing.

Each group is 5 shots, unless the chronograph didn't pick up 5 shots and I shot more to get a consistent numbers. Where you are seeing the +1 turn and then just +1 etc this is the hammer spring adjuster on the rear. I marked the adjuster just like I showed when I was playing with the AAA HPS30. This helps in keeping things consistent and easy to index. I REALLY wish companies would add hash marks around the outside of the adjuster to help in tuning. Would be a great little addition that wouldn't add to much to the overall cost of the rifle.

I was doing rough adjustments on the rifle to see what I was able to accomplish. The 25 grain range of slugs shot great and I could feel a difference in the shot cycle when shooting. There didn't seem to be as much stress on the rifle and the valving sounded smoother while cycling. I did shoot some 30 and 34 grain Javelin V2 slugs just to see what speeds I can get. I was able to get close to 900 fps with the 34 grain slugs and there was still more hammer tension I could add. Now I didn't adjust the regulator as I didn't have any of my equipment to adjust and don't want to adjust just yet. Saying that the felt recoil was quite a bit more when going with the 34 grain slugs. You could really feel these slugs when shooting and I was honestly shocked. I have no doubt that the gun will shoot them but the effect it will have on the shot count is unknown at this point.

Speaking of shot count........ The rifle fills to a max of 250 bar. I was able to shoot 2 targets, so 10 shots with only 10 bar of pressure lost. I am looking at getting a digital gauge for the rifle so I can see exactly what the efficiency of the rifle is. But being as my main focus is to use this rifle for NRL22 matches, having 12 full powered shots I am ok with the shot count at this point.

Over all I am looking at the Corbin .218 X Hollow Point, this is one of their newer products, and they were shooting shockingly good. At the end of the session I was shooting from 25, 50, 75, and 100 yards at a new bull for each distance. And you can see the dispersion but it was consistent and I can't wait to get the gun out and hopefully shooting a few gophers and bunnies with it. My shooting buddy and I have been talking with Corbin and will be working on getting videos and pictures while using them ;) The other slugs I am going to play more with are the H&N Slug HP that are 25 grains as well as the JSB KnockOut in the 25.39 grains, both in the .217 size. This is what kind of confused me and frustrated me..... is the rifle was shooting both of these sizes very well!

I did start the 50 yard page with just a naked barrel. There was the adapter for the DonnyFL Ryu quick release adapter on the end, but no muzzle break or anything like that. I wanted to see what the rifle would do with a bare barrel and then add a moderator or muzzle break to see, if any, difference these will have on the groups. I do have a DonnyFL Ryu and Yokozuna, and Impulse Air 1350, a muzzle break that I purchased from South Africa, and a tunable muzzle break from Eagle Vision. I will get a group picture of them all so we can all see what is going on.

Over all I left the range with one heck of a headache, and ready to get home and shower. Being as I went from my job right to the range I was gross and slimy from a rough day at work. I am going to do more work and testing to get these groups as small as possible. If there is anything you guys want to see or want tested just let me know. I will see what I can do and give them a shot.

One thing I did notice is that the H&N slugs I had previously had, and finished off at the range, had a weird waxy lubricant on them. But the tin I opened up during this shooting session the slugs looked clean and didn't have that waxy looking appearance to them? I am also debating on trying some of the JSB KnockOuts in the V2. Not sure there will be any difference between the flat walled V1 and the flared base of the V2.



View attachment 6303View attachment 6304
So the regulator is still set at the level that Martin set it at for shooting the .22 caliber 25 grain redisign's? Or did you get it tuned to shoot heavier slugs from the start? If it's still set at the level for shooting the 25 grain pellets then you will get alot more power out of it when you turn that regulator up. I'm afraid that having martin tune mine for 30 grain slugs at 970 fps. with no external plenum will make it shoot to harsh, like to much recoil. What do you think?
 
Yeah the regulator is still set the way Martin set it, and it was set for 25 grain slugs. Yes I could bump it up a bit, and I am looking at a adapter to allow me to see the regulator pressure.

Add the external plenum and it should be fine. I am going to talk to my buddy to see if he can make me some 28-30 grain x point slugs for me to try.
 
Yeah the regulator is still set the way Martin set it, and it was set for 25 grain slugs. Yes I could bump it up a bit, and I am looking at a adapter to allow me to see the regulator pressure.

Add the external plenum and it should be fine. I am going to talk to my buddy to see if he can make me some 28-30 grain x point slugs for me to try.
Huma makes a regulator gauge that fits into the bottom blanking plug, I'm gonna order it right now
 
Isn't there a difference between the hm1000 and the hm1000x? That would be my only fear about ordering something. I am going to check around my shop to see if I have the correct adapter to make a tester.
 
Screenshot_20240522_173054_FX Radar.webp

Here is a screen shot from some 40 grain slugs. They were really slow, but at 20 feet they were a single hole. Lol

Javelin V2 .217 40 grain
 

Create an account or login to comment

You must be a member in order to leave a comment

Create FREE account

Create a FREE account on our community. It's easy!

Log in

Already have an account? Log in here.

Trending in this forum

Back
Top