Maintenance Where to find Evol tools?

[Smok3y]

NOT meant to be a WTB ad, but not having luck finding the Evol tools, especially the barrel tool. I want to know if I buy the rifle, that I can still break it down to replace orings or adjust the reg if needed (don’t really want to do either!).

Anyone know of a dealer with the tools? I can’t find any expect the gauge tool.

Maybe just buy a strap wrench instead?

 

[Airgun-hobbyist]

NOT meant to be a WTB ad, but not having luck finding the Evol tools, especially the barrel tool. I want to know if I buy the rifle, that I can still break it down to replace orings or adjust the reg if needed (don’t really want to do either!).

Anyone know of a dealer with the tools? I can’t find any expect the gauge tool.

Maybe just buy a strap wrench instead?

I made a single pin tool before they were available from AAA, and bought the good oem tool as soon as they were available. A strap wrench or even a pin type of spanner will likely mar up your gun. The tools are priceless and top quality, just like the rifles. Contact AoA or AAA through their web sites, or even message Tom here to place an order. It is hard to find any manufacturer of anything nowadays as accessible as this. Back when Tom first showed off the raw unfinished barrel removal tool, per my request, he engraved the "Slayer" logo on the other side. Good dude right there.

 

[Smok3y]

The tool to remove the barrel is hard to find. I have an Evol .30 that I bought in 2022. It is very difficult and can damage the rifle if you try to take apart your evol without the pink Barrel Removal Tool. The thread lining of the airtank is very thin. If you try to bend the barrel shroud up instead of removing it, you can cause the tank to completely freeze while you are unscrewing it. Trust me. It is VERY much worth it to buy the tool. It's only $100. The Evol is a $3000 precision air rifle. Once you buy it, you will be able to disassemble it without any galling. I have an Evol and I've taken it apart. If I could go back, I would buy the Epic 2 PCPAir Rifle ((not the EPOCH!!!). It is almost identical to the Evol. And costs less.The Epic 2 can get 80 ft. Lbs with a .25 instead of a .30. They .30 are expensive.

It isn’t about money, as I would rather have one. I’m looking to find one, but they aren’t in stock anywhere that I can find.

@Airgun-hobbyist Spoke to AoA today and called a couple others this week and none have them either.

 

[Airgun-hobbyist]

It isn’t about money, as I would rather have one. I’m looking to find one, but they aren’t in stock anywhere that I can find.

@Airgun-hobbyist Spoke to AoA today and called a couple others this week and none have them either.

Gotcha. Try these: There's an email link here, American Air Arms – Made in the USA Or try messaging @American Air Arms with the tool request through this forum.

 

[fderry]

NOT meant to be a WTB ad, but not having luck finding the Evol tools, especially the barrel tool. I want to know if I buy the rifle, that I can still break it down to replace orings or adjust the reg if needed (don’t really want to do either!).

Anyone know of a dealer with the tools? I can’t find any expect the gauge tool.

Maybe just buy a strap wrench instead?

Here is the link to AoA's listing for the AAA tools they carry.

Daystate DISCONTINUED Daystate Wolverine HP - Precharged (PCP)

<p>Product Development and design is an arduous task with no guarantees of success. Companies have been rocketed to the top of their industry, or fallen into oblivion by investing time and resources in the right or wrong product. The world of precision airguns is a dangerous place for new...

www.airgunsofarizona.com

 

[pan60]

Tom told me not to long ago tools where coming. I would assume ( only my assumption ) about the time the new guns are out or shortly after.

 

[Smok3y]

Here is the link to AoA's listing for the AAA tools they carry.

Daystate DISCONTINUED Daystate Wolverine HP - Precharged (PCP)

<p>Product Development and design is an arduous task with no guarantees of success. Companies have been rocketed to the top of their industry, or fallen into oblivion by investing time and resources in the right or wrong product. The world of precision airguns is a dangerous place for new...

www.airgunsofarizona.com

Thanks. Their site and Jacob both say they are sold out… that’s why I’m looking for them.

 

[Ezana4CE]

@Smok3y Have you considered using a spanner wrench to remove the barrel? Aside from that what else do you need?

 

[Jessairz]

It isn’t about money, as I would rather have one. I’m looking to find one, but they aren’t in stock anywhere that I can find.

@Airgun-hobbyist Spoke to AoA today and called a couple others this week and none have them either.

Honestly, I don't know where to find EVOL tools. I haven't really looked because is absolutely freezing outside and I don't want to bring my Huben nor EVOL outside in this weather. Sorry I cant be of more help.

 

[Smok3y]

@Smok3y Have you considered using a spanner wrench to remove the barrel? Aside from that what else do you need?

I don’t have one yet, but yes I have considered alternative tools. You have one, you tell me if I need anything else. They make 3 tools, but it sounds like most people say you only need 2 of them. I have read thru all the threads here and AGN over the years and people have mentioned you don’t need them, and you also see the rifles where people didn’t think they need them and it shows.

At this point, the reason I don’t have one is that I don’t have the tool to break it down (if needed) to be able to adjust for different pellets. In 22, I like to be able to shoot several weights.

I have waited over 1.5 years for the new version, so maybe this is the year. It is probably the only big name brand I haven’t tried, but I’m still hoping to.

 

[Ezana4CE]

I don’t have one yet, but yes I have considered alternative tools. You have one, you tell me if I need anything else. They make 3 tools, but it sounds like most people say you only need 2 of them. I have read thru all the threads here and AGN over the years and people have mentioned you don’t need them, and you also see the rifles where people didn’t think they need them and it shows.

At this point, the reason I don’t have one is that I don’t have the tool to break it down (if needed) to be able to adjust for different pellets. In 22, I like to be able to shoot several weights.

I have waited over 1.5 years for the new version, so maybe this is the year. It is probably the only big name brand I haven’t tried, but I’m still hoping to.

@Smok3y I don't know what you need. Personally, I've used the barrel too and manometer tool. I mentioned the spanner wrench because I've read of others using or mentioning that tool. If you've read any of my Evol posts you'd know that I am of the opinion that this isn't an easy platform to work on, so my disassembly of my Evol has been minimal. Your mileage may vary.

 

[Gear_Junkie]

The thread lining of the airtank is very thin. If you try to bend the barrel shroud up instead of removing it, you can cause the tank to completely freeze while you are unscrewing it.

I've always understood these EVOL's to be built like tanks. The thin airtank at the threads sounds a little concerning??? I've never seen a cross section of the tube so I am mainly just curious about this.

 

[Airgun-hobbyist]

I've always understood these EVOL's to be built like tanks. The thin airtank at the threads sounds a little concerning??? I've never seen a cross section of the tube so I am mainly just curious about this.

It should not be concerning. It is a perfect thread job for both materials, but does need attention to detail in both assembly and disassembly. Not using the correct tool for the disassembly job and prying the barrel and air cylinder apart from each other to remove the air cylinder causes thread damage. That is a lot of leverage on both parts, especially at the threads in partial disassembly, and something has to give in one way or another.

 

[pan60]

I've always understood these EVOL's to be built like tanks. The thin airtank at the threads sounds a little concerning??? I've never seen a cross section of the tube so I am mainly just curious about this.

It should not be concerning. It is a perfect thread job for both materials, but does need attention to detail in both assembly and disassembly. Not using the correct tool for the disassembly job and prying the barrel and air cylinder apart from each other to remove the air cylinder causes thread damage. That is a lot of leverage on both parts, especially at the threads in partial disassembly, and something has to give in one way or another.

not only should it not be concerning remember its not aluminum but rather magic light weight space age super strong alien material

 

[Madeintheuk]

Just wondering. Does the tool to remove the epic 2 barrel work on the evol? Another avenue to possibly check out.

 

[ctshooter]

I would not take Epic over AAA. I own/have owned both brands. The Epic is not a better version of the EVOL. It's not even an apples to apples comparison as the current EVOLs on the market all have traditional hammer/valve configuration. The Epic has a balanced valve - so that would need to be compared with the new HPS. Epic's balanced valve has a lot of stiction issues when not shot for a while - never had a stiction issue in my Slayer. You cannot compare an Epic in .25 with 80 fpe to a EVOL in .30 with the same - again balanced valved makes the difference there.

Now - to the OP's questions on tools. If you want to adjust power you only need 1 of the 3 tools. That being the spanner or barrel wrench. The only alternative I have used - and I must specify be VERY CAREFUL or risk scratching the barrel - is an AR castle nut wrench. It will fit the hole and give you the leverage needed to loosen the barrel - but you'll need to pad where the wrench rubs the outside of the barrel.

Just wondering. Does the tool to remove the epic 2 barrel work on the evol? Another avenue to possibly check out.

No - the AAA barrel tool does not fit the Epic barrel. The holes on the Epic are a touch too small.

 

[Smok3y]

I would not take Epic over AAA. I own/have owned both brands. The Epic is not a better version of the EVOL. It's not even an apples to apples comparison as the current EVOLs on the market all have traditional hammer/valve configuration. The Epic has a balanced valve - so that would need to be compared with the new HPS. Epic's balanced valve has a lot of stiction issues when not shot for a while - never had a stiction issue in my Slayer. You cannot compare an Epic in .25 with 80 fpe to a EVOL in .30 with the same - again balanced valved makes the difference there.

Now - to the OP's questions on tools. If you want to adjust power you only need 1 of the 3 tools. That being the spanner or barrel wrench. The only alternative I have used - and I must specify be VERY CAREFUL or risk scratching the barrel - is an AR castle nut wrench. It will fit the hole and give you the leverage needed to loosen the barrel - but you'll need to pad where the wrench rubs the outside of the barrel.


No - the AAA barrel tool does not fit the Epic barrel. The holes on the Epic are a touch too small.

This is good info in the barrel tool. Thanks!

 

[Airgun-hobbyist]

This is good info in the barrel tool. Thanks!

A couple of things to note if using an AR barrel tool... The AR spanner wrench may possibly work, but will depend on how old your particular Evol is. If you have a newer style of reciever with the extended picatinny rail then you have limited room for even a conventional spanner wrench. I made a spanner using my drill press and files years ago to work on my first Evol. It took some measuring, fitting, and trial and error to get right, and I still bought the AAA tool when he first offered it. The anodized tool is "priceless" as they say.

 

[Dairyboy]

I'd agree only the barrel tool is necessary. The newer Evols gauges are sealed by oring so no longer have to be tight to seal.

 

[ctshooter]

A couple of things to note if using an AR barrel tool... The AR spanner wrench may possibly work, but will depend on how old your particular Evol is. If you have a newer style of reciever with the extended picatinny rail then you have limited room for even a conventional spanner wrench. I made a spanner using my drill press and files years ago to work on my first Evol. It took some measuring, fitting, and trial and error to get right, and I still bought the AAA tool when he first offered it. The anodized tool is "priceless" as they say.

Yes - valid point. As I recall now it was an earlier model EVOL where the scope rail did not extend out over the barrel. I got the tool shortly thereafter so I never considered that an AR wrench would have an issue getting around the extension of the scope rail.

I believe the tools were made from unobtanium. Good luck on your hunt.