Install the app
How to install the app on iOS

Follow along with the video below to see how to install our site as a web app on your home screen.

Note: This feature may not be available in some browsers.

What'cha doing air gun related today?

Last 1 of these i got from aoa cause i couldn’t find 1 anywhere else cost me $100
That British pellet pouch is wet molded, and I can't see it clearly enough, but I think it is glued with minimal stiching, I am working on a design for a round pellet pouch with a magnetic clasp "lid" and a belt clip. I am thinking that it can be clipped on a belt, or on the outside of your front pocket, at the same place we all clip our knives.

I will post pics of my prototype. Its mostly designed on my software, but will report back!
 
That British pellet pouch is wet molded, and I can't see it clearly enough, but I think it is glued with minimal stiching, I am working on a design for a round pellet pouch with a magnetic clasp "lid" and a belt clip. I am thinking that it can be clipped on a belt, or on the outside of your front pocket, at the same place we all clip our knives.

I will post pics of my prototype. Its mostly designed on my software, but will report back!
It’s definitely wet molded and probably glued with Barge Cement. It’s very nicely cut and finished and well worth the price. I look forward to seeing your design.
 
OK dont laugh. Awl In prototype number uno. I don't find the neck lanyard particularly useful, but I can make one. I like the clip. Iv'e tried it clipped to my pocket, and I could get a pellet out with one hand. It could clip on a belt as well, and I haven't considered other options, but I will contemplate it. This would be useful for the single shot types; springers most likely.

It is simple veg tan leather. ~6oz on the sides and 4oz gusset/top. THe clip is screwed on with chigago studs, and the leather is treated with bees wax. I use a heat gun to melt it into both sides of the leather. Stitched with 1mm Ritza tiger thread in burgundy. The clasp is magnetic and seems to hold well. inside width is about 3/4" and it is about 2.5" diameter on the side pieces. Total OD a little bigger. Oh, and there is only a tiny bit of Barge, which I used to hold the strap snap in place before I stitched it. Note the hardware is hidden. Otherwise all hand stitched.

This is my first one, so once I figure out what will work best, then I can embellish it with better leather, liner, maybe conchos or studs or the like. I can also engrage any graphic on it too.

Let me know what you think! Good, bad or otherwise; got no ego anymore.




1.webp2.webp3.webp4.webp
 
Looks good. That was pretty darn quick. I would definitely look at a lanyard option as well. I could be wrong, but I imagine that the idea of hanging it around your neck is that it keeps them close to your rifle and within reach without putting your rifle down. I could be completely wrong on that though. I’ve always thought they were a Field Target thing. Great job.
 
Looks good. That was pretty darn quick. I would definitely look at a lanyard option as well. I could be wrong, but I imagine that the idea of hanging it around your neck is that it keeps them close to your rifle and within reach without putting your rifle down. I could be completely wrong on that though. I’ve always thought they were a Field Target thing. Great job.
Field target and hunting is what i use them for. Most all of my guns are set up single shot.
 
OK dont laugh. Awl In prototype number uno. I don't find the neck lanyard particularly useful, but I can make one. I like the clip. Iv'e tried it clipped to my pocket, and I could get a pellet out with one hand. It could clip on a belt as well, and I haven't considered other options, but I will contemplate it. This would be useful for the single shot types; springers most likely.

It is simple veg tan leather. ~6oz on the sides and 4oz gusset/top. THe clip is screwed on with chigago studs, and the leather is treated with bees wax. I use a heat gun to melt it into both sides of the leather. Stitched with 1mm Ritza tiger thread in burgundy. The clasp is magnetic and seems to hold well. inside width is about 3/4" and it is about 2.5" diameter on the side pieces. Total OD a little bigger. Oh, and there is only a tiny bit of Barge, which I used to hold the strap snap in place before I stitched it. Note the hardware is hidden. Otherwise all hand stitched.

This is my first one, so once I figure out what will work best, then I can embellish it with better leather, liner, maybe conchos or studs or the like. I can also engrage any graphic on it too.

Let me know what you think! Good, bad or otherwise; got no ego anymore.




View attachment 24342View attachment 24343View attachment 24344View attachment 24346
So, now you have me thinking of your next possible airgun product LOL. I’m sure there’s a market for leather mag holders : singles, doubles, triples. Clip-ons, belt slides etc.. Sorry, I can’t help myself LOL. NOTE to self, no more leather work. These deserve a thread of their own.
 
Drug the impact out kicking and screaming this morning. Knocked down 8 bowling pins at around 35 yards. To easy! That's probably why I usually grab one of my hatsans to plink with.
 

Create an account or login to comment

You must be a member in order to leave a comment

Create FREE account

Create a FREE account on our community. It's easy!

Log in

Already have an account? Log in here.

Trending in this forum

Back
Top