Airgun barrel cleaning – do you need to do it? That’s a question that appears every so often among airgunners. And yet the answer seems to vary with the gun and pellets in use.
Certainly, HAM Contributor Matt Coulter found airgun barrel cleaning to be extremely important in his recent story on shooting slugs in his Cricket 2 Tactical (which has a Lothar Walther barrel). In this case, he found an average improvement (reduction) in group size to be no less than 74%.
My personal experience is that I’ve never found that much improvement in accuracy when shooting conventional lead pellets. But then, I’ve never tried to make a specific test on that subject.
Fortunately, HAM Tester Eric Brewer has given us some data to work with! Recently, a .177 caliber Umarex Emerge air rifle arrived in the HAM offices for testing. As our chief springer tester, Eric took the gun. You’ll read his test review soon.
After some initial evaluation, Eric felt that the gun had been shot before (we do not always receive new guns for testing). So he produced some test targets with the gun in “as received” condition. Here’s the 10 Yard target for H&N Baracuda Match pellets.
Then he cleaned the barrel.
Our heading photograph shows the patch that came out of the barrel. This gun had definitely been shot. A lot!
After Eric had cleaned it the accuracy was improved by 66%. It looked like this…
Averaging Eric’s results, we find an average improvement in accuracy after airgun barrel cleaning of 29%. Sure that’s not as much as Matt found when testing slugs, but it’s a very satisfactory improvement!
Here’s Eric’s findings in detail. The group sizes are a simple multiplication of the horizontal and vertical CTC (Center-to-Center) measurements.
What’s particularly interesting is that the Crosman Premier Hollow Point pellets showed no improvement from the barrel cleaning at all. In fact the accuracy was slightly worse after cleaning!
However there was a very significant improvement for each of the H&N pellets Eric tested. The average was 49.9% reduction in group size.
Why could that be? We think that it could be because the Crosman pellets are manufactured from very hard lead alloy. H&N uses an obviously much softer alloy.
What we are sure of is that one test does not give all the answers to the question of do you need airgun barrel cleaning. But it has set us up to think more about this issue!
For information, Eric cleaned the barrel using a pull-through soaked in Break Free. He followed that with 3 more “wet” patches and 2 dry patches. This left a “fairly clean” barrel which he then seasoned before further testing by firing 10 Crosman Premier HP pellets.
BUY FROM PYRAMYD AIR
The post Airgun Barrel Cleaning – Do You Need To Do It? appeared first on Hard Air Magazine.
Continue reading...
Certainly, HAM Contributor Matt Coulter found airgun barrel cleaning to be extremely important in his recent story on shooting slugs in his Cricket 2 Tactical (which has a Lothar Walther barrel). In this case, he found an average improvement (reduction) in group size to be no less than 74%.
My personal experience is that I’ve never found that much improvement in accuracy when shooting conventional lead pellets. But then, I’ve never tried to make a specific test on that subject.
Fortunately, HAM Tester Eric Brewer has given us some data to work with! Recently, a .177 caliber Umarex Emerge air rifle arrived in the HAM offices for testing. As our chief springer tester, Eric took the gun. You’ll read his test review soon.
After some initial evaluation, Eric felt that the gun had been shot before (we do not always receive new guns for testing). So he produced some test targets with the gun in “as received” condition. Here’s the 10 Yard target for H&N Baracuda Match pellets.
Then he cleaned the barrel.
Our heading photograph shows the patch that came out of the barrel. This gun had definitely been shot. A lot!
After Eric had cleaned it the accuracy was improved by 66%. It looked like this…
Averaging Eric’s results, we find an average improvement in accuracy after airgun barrel cleaning of 29%. Sure that’s not as much as Matt found when testing slugs, but it’s a very satisfactory improvement!
Here’s Eric’s findings in detail. The group sizes are a simple multiplication of the horizontal and vertical CTC (Center-to-Center) measurements.
| Pellet | Group Before Cleaning | Group After Cleaning | Improvement |
|---|---|---|---|
| RWS Hobby | 1.61 Sq. In. | 1.32 Sq. In. | 17.90% |
| Crosman Premier HP | 0.78 Sq. In. | 0.79 Sq. In. | 1.51% |
| H&N Field Target Trophy | 1.44 Sq. In. | 0.73 Sq. In. | 49.24% |
| JSB Exact | 1.44 Sq. In. | 1.31 Sq. In. | 9.09% |
| Baracuda Match 10 Yds | 0.73 Sq. In. | 0.25 Sq. In. | 66.39% |
| Baracuda Match 25 Yds | 2.92 Sq. In. | 1.92 Sq. In. | 34.01% |
What’s particularly interesting is that the Crosman Premier Hollow Point pellets showed no improvement from the barrel cleaning at all. In fact the accuracy was slightly worse after cleaning!
However there was a very significant improvement for each of the H&N pellets Eric tested. The average was 49.9% reduction in group size.
Why could that be? We think that it could be because the Crosman pellets are manufactured from very hard lead alloy. H&N uses an obviously much softer alloy.
What we are sure of is that one test does not give all the answers to the question of do you need airgun barrel cleaning. But it has set us up to think more about this issue!
For information, Eric cleaned the barrel using a pull-through soaked in Break Free. He followed that with 3 more “wet” patches and 2 dry patches. This left a “fairly clean” barrel which he then seasoned before further testing by firing 10 Crosman Premier HP pellets.
BUY FROM PYRAMYD AIR
Umarex Emerge Multi-shot Rifle 0.177
The post Airgun Barrel Cleaning – Do You Need To Do It? appeared first on Hard Air Magazine.
Continue reading...
Usually also, if I switch to another slug or pellet type and then shoot a magazine full (12-13 shots) to prepare the barrel for that projectile 
