Install the app
How to install the app on iOS

Follow along with the video below to see how to install our site as a web app on your home screen.

Note: This feature may not be available in some browsers.

Benchrest Ideal way of testing rifle for accuracy.

Penfold

HAM Shooter
48
165
Country flag
When I first bought my 9015 it didn't shoot all that well.
It would flick the odd shot quite randomly.
So I bunged it in a floor mounted machine rest at our range (indoors 25 yards).
If you really want to see how your rifle performs, then this is the way (takes away any input from the squishy human at the blunt end of the rifle).
Photos show the machine rest, and a view down our range, plus a couple of the target sheets (these are just a blank paper as I'm not aiming at a specific point. Just bunging in 10 or 20 shots at the paper to see how the rifle groups). You can see the odd flier showing up. The groups aren't too shabby...but I wanted better.
I added the red arrow with Photoshop to point out the blank sheet of paper I'm shooting at.
Any of the groups would sit nicely inside the 10 ring of a target, but I wanted them to be even tighter.
Now I have sorted out the bad muzzle job that Anschutz did I have yet to return to the machine rest...and I probably won't bother as those weird fliers have now gone.
Edit: Our range can hold 18 shooters, with 9 at ground level and 9 above on the mezzanine floor.

Vise.webp

SANY0058.webp

SANY0061.webp

SANY0073.webp
 
I shot these targets during pellet testing to see what pellets my new rifle liked. It was a few weeks later that I discovered the muzzle problem. That dodgy muzzle helped explain why I was getting fliers.
Not a fault with the pellets at all.
 
When I first bought my 9015 it didn't shoot all that well.
It would flick the odd shot quite randomly.
So I bunged it in a floor mounted machine rest at our range (indoors 25 yards).
If you really want to see how your rifle performs, then this is the way (takes away any input from the squishy human at the blunt end of the rifle).
Photos show the machine rest, and a view down our range, plus a couple of the target sheets (these are just a blank paper as I'm not aiming at a specific point. Just bunging in 10 or 20 shots at the paper to see how the rifle groups). You can see the odd flier showing up. The groups aren't too shabby...but I wanted better.
I added the red arrow with Photoshop to point out the blank sheet of paper I'm shooting at.
Any of the groups would sit nicely inside the 10 ring of a target, but I wanted them to be even tighter.
Now I have sorted out the bad muzzle job that Anschutz did I have yet to return to the machine rest...and I probably won't bother as those weird fliers have now gone.
Edit: Our range can hold 18 shooters, with 9 at ground level and 9 above on the mezzanine floor.

View attachment 14867

View attachment 14868

View attachment 14870

View attachment 14871
Those targets look awfully GOOD to me! It doesn't look like anything is wrong with the rifle. Of course, it isn't perfect and nearly anything can be made better; however, that's one good set of targets. I ASSUME these are three shots or so. If these are 10 to 20 shot groups at 25 yards, I think you have a rifle that can't be improved upon. If the JSB was one shot it keyholed. If it is ten shots, WOW. AD2
 
Yes, all were 10 shot groups.
But...I have improved the rifle a bit.
After cutting the outer shroud back by 95mm to allow access to the muzzle I faced the muzzle nice and flat in the lathe (at a 10° angle...just 'because').
The rifle had been supplied from Anschutz with the most messed up muzzle I have ever seen (bad show Anschutz).
Then later on I removed the barrel band and fitted a carbon fibre tube over the length of the barrel. The tube was cut long to replace the 'missing' 95mm...in fact I made it a wee bit longer to match up with the slightly extended length of the air cylinder after the fitting of a Josef1000 quick connect.
So the barrel and air cylinder are now free floating (apart from a soft foam strip under the front of the air cylinder).
I also did a fibreglass bedding job under the action area too.
Did all that help? Well yes, I reckon it has...
The photo is a group I shot when checking out some H&N pellets. This was shot from the benchrest using my AR250 front rest, and SEB Lowline rear bag.
Yes...I reckon it's an improvement.
Fired the top group first, then 1 click right on the windage and fired the 2nd group.
Yep...that'll do!
 

Attachments

  • H&N-FTT.webp
    H&N-FTT.webp
    75.4 KB · Views: 11
Yes, all were 10 shot groups.
But...I have improved the rifle a bit.
After cutting the outer shroud back by 95mm to allow access to the muzzle I faced the muzzle nice and flat in the lathe (at a 10° angle...just 'because').
The rifle had been supplied from Anschutz with the most messed up muzzle I have ever seen (bad show Anschutz).
Then later on I removed the barrel band and fitted a carbon fibre tube over the length of the barrel. The tube was cut long to replace the 'missing' 95mm...in fact I made it a wee bit longer to match up with the slightly extended length of the air cylinder after the fitting of a Josef1000 quick connect.
So the barrel and air cylinder are now free floating (apart from a soft foam strip under the front of the air cylinder).
I also did a fibreglass bedding job under the action area too.
Did all that help? Well yes, I reckon it has...
The photo is a group I shot when checking out some H&N pellets. This was shot from the benchrest using my AR250 front rest, and SEB Lowline rear bag.
Yes...I reckon it's an improvement.
Fired the top group first, then 1 click right on the windage and fired the 2nd group.
Yep...that'll do!
Now, I'm a huge fan of doing things myself on the middle of the road guns that I like to work on, but I'd be rather upset about having to re-do the muzzle of an Anschutz 9015. I would have sent it back on principle, just so they had to spend some money to fix their mistake on a barrel that costs a lot already and is only bought because of an expectation of quality in the first place. I'm happy for your success with it, but I'm not happy that Anschutz got off the hook for shoddy work.
 
Anschutz quality has dropped off now...and they don't care.
They told me that my rifle reached their standard of accuracy (so go pound sand sort of thing).
No problems. I can do a better job than some shoddy wee German anyway. I wouldn't trust ever sending it back for them to 'fix'.
It's fine now. Shoots very well.
The only let down is the squishy human hanging on the blunt end of it.
 
Anschutz quality has dropped off now...and they don't care.
They told me that my rifle reached their standard of accuracy (so go pound sand sort of thing).
No problems. I can do a better job than some shoddy wee German anyway. I wouldn't trust ever sending it back for them to 'fix'.
It's fine now. Shoots very well.
The only let down is the squishy human hanging on the blunt end of it.
I completely understand not wanting to subject anything of value to a shipping experience twice in a lifetime. Jesus, these days I won't subject myself to travel on airplanes, what a zoo.
 
I completely understand not wanting to subject anything of value to a shipping experience twice in a lifetime. Jesus, these days I won't subject myself to travel on airplanes, what a zoo.
None of my guns are of high value (except maybe my older HM1000X) so I don't mind breaking and fixing my own guns. I also, at 69, still fly 6-10 times a year on business and other than slogging through the big airports between gates (Monday Denver C58 to C31) I like flying. I also tend to fly Southwest and am usually in the first 5 on the plane for "THE SEAT". No, those are shoes not water skis.20251020_101435.webp
 

Create an account or login to comment

You must be a member in order to leave a comment

Create FREE account

Create a FREE account on our community. It's easy!

Log in

Already have an account? Log in here.

Trending in this forum

Back
Top