A Close Look At The JTS AirStryke Carbine

Today we’re taking a close look at the JTS AirStryke Carbine. Hard Air Magazine readers first saw this model in our report from the 2026 IWA OutdoorClassics exhibition.

Now one has arrived in the HAM offices and we can really examine what this new model brings to the table.

As it’s name implies, the JTS AirStryke Carbine is a shortened version of the HAM Gold Award-winning AirStryke. So, having reviewed the “full length” AirStryke so recently, we have a “lite” test format for the carbine.

BUY FROM PYRAMYD
JTS AirStryke Carbine PCP Air Rifle 0.22​

SHOOTABILITY​

Immediately I’m going to say that this .22 caliber, regulated carbine is a compact, lightweight and easy-to-shoot airgun. With the collapsible stock, adjustable cheekpiece and good balance, this is a PCP air rifle that can be used comfortably by shooters of any physique.

The quoted overall length of 33 Inches is actually with the stock fully extended. With the stock pushed right in the overall length comes down to only about 30 Inches. Ideal for a truck gun!

Weight in shooting trim is 5 Lbs 11 Oz. Yes, this carbine is both compact and light.

But – if you want to mount it on a bipod – go right ahead. The Leapers UTG rubber-armored model works a treat…

The JTS AirStryke Carbine is aimed directly at those shooters who bemoan the lack of open sights on the overwhelming majority of recent PCP air rifles. We’ll find out more below…

Filling with High Pressure Air is undertaken with a capped “Foster-style” quick disconnect at the front of the tube. Maximum fill pressure is a hand pump-friendly 3,000 PSI.

Even better is that the clear, well-marked HPA pressure gauge is set to be read from the side of the gun. No more “looking down the barrel to read the gauge”.

This is excellent and shows that such a feature can be incorporated in even a value-priced PCP air rifle like the JTS AirStryke Carbine. The gauge itself has a clearly-marked faceplate, combined with an obvious red, overfill-indicator zone. Outstanding!

At the rear, the Carbine has a cheek riser that adjusts to four different height settings. In combination with the AR-style grip, this makes it easy to achieve a consistent cheek weld and hold – an often-overlooked aspect of practical accuracy downrange.

SIGHTS AND SCOPE​

But now let’s get to the main issue. Those open sights!

The rear sight is different from the rear sight of the full-length AirStryke. It’s mounted at the rear of the receiver and has click-adjustable windage with two “flip over” choices for elevation – just like a good old M1 Carbine.

Up-front, there’s an unprotected blade front sight.

Plus the barrel is equipped with a 1/2-In UNF thread under that cover. This allows a dedicated airgun silencer to be attached where legal. That would be a good thing as I found the carbine to be fairly loud, courtesy of the short barrel.

Now it’s here that I’m calling-out to those open-sight devotees. You NEED to buy this gun!

For the fact is that the AirStryke Carbine is practically unable to use a riflescope. Trust me on this, I tried…

Having failed to mount multiple conventional scopes, I finally found that an ultra-compact Leapers UTG Bugbuster would fit. Just.

However the rear sight partially occludes the scope’s eyepiece. Not ideal.

Oh and there’s no way to remove the rear sight. Tried that!

So what to do?

Well as my eyes are completely unable to aim with open sights now – it’s tough getting old – I found that a Leapers UTG red/green dot sight was an ideal solution. Problem solved!

BUY FROM PYRAMYD
1×32.5mm ITA Combat Red/Green Dot Sight, 1/2 MOA, 38mm Tube, Riser, Quick-Detach Weaver/Picatinny Mount

POWER AND CONSISTENCY​

The combination of the JTS Carbine and UTG dot sight was good and I had considerable success engaging feral soda cans – my favorite targets – in informal testing out to 30 Yards or so.​

Shooting 16.08 Grain JTS Dead Center pellets, this AirStryke Carbine generated an average Muzzle Energy of 22.12 Ft/Lbs – that’s 787 FPS. This is plenty for the plinking, squirrel control and similar purposes that this gun is designed for.

It’s about 2 Ft/Lbs down on the Muzzle Energy of the long AirStryke That’s no surprise given the shorter barrel length.

As we expected, the Standard Deviation for Carbine was very low. I was impressed, but not surprised by this as it reflects the consistency of the full-length AirStryke we tested in 2025.

The chart below shows that the regulator was certainly doing its job, with an average Standard Deviation of 3.61 FPS across 24 shots before the regulator set point was reached on the test gun. Excellent!

TRIGGER AND COCKING EFFORT​

Again, very similar to the full length AirStryke. The average pull weight of “our” carbine was 2 Lbs 8.5 Oz. This was very close to the 2 Lb 10.8 Oz average of the long AirStryke and is another testament to manufacturing consistency at the JTS factory.

Trigger and cocking lever feel were identical, too.

CONCLUSION​

If you are looking for an attractively-priced, compact, light PCP, this carbine could be a great choice so long as you want to use open sights or a red dot sight.

BUY FROM PYRAMYD
JTS AirStryke Carbine PCP Air Rifle 0.22​

The post A Close Look At The JTS AirStryke Carbine appeared first on Hard Air Magazine.

 

[Doc Holiday]

Ok I’ll play devil’s advocate. As an open sight guy, how can a good sight picture be obtained with an open notch rear sight that is placed at the very back of the gun. Most all usable blade sights are mounted forward of the receiver, actually on the barrel. The successful rear receiver open sights is a peep.

 

[Rick64]

Looks like a decent little carbine for squirrels and rabbits

 

[Jaabaa]

Seen Alot of good things on it so far.

 

[Luis Leon]

Seems a dandy lil PCP, JTS needs to make the rear sight removable. That alone would make scope mounting easier and make it more attractive to many. Iron sights (sidearms aside) are overrated for this old geezer. My poor eyes demand optics… I bet small critters, sub 50 yards will find it irresistible.