Search results

I shot the 30 cal Ghost today. Trying to get it ready for EBR! The 110 Reg pressure with 7 on the hammer was best today. It was in the low 890's The group sizes were .453 MOA, .817 MOA, .451 MOA for an average of .577 MOA. Groups were shot at 75 yards with light switching winds 3-6 mph.

Length I'm thinking 2 weeks but have the option to renew for free. Point to post = How about what ever level would let 80% of the people post.

Joey sorry for the late response. I use the 3M polish cloths. The Pink green and white. I cut them into thin strips and wing them onto a cotton mop. I use an old cleaning rod I cut off and put into drill. I do it from both ends of the barrel while it is in a vise as to round off both sides...

I agree with all the above. Yes turn the reg down, my Ghosts came to me shoot near sonic (30 cal shooting over 1000 fps). Yes clean the barrel, then polish the barrel. Polish until you think your there, then you might be half way to where the best is.

Thanks, I saw that on the other forum but try and avoid it do to an event. I was just hoping someone closer to K&L might enlighten us all.

I made an order back in June and haven't heard anything. I have tried calling and emailing but still get no answer back. Does anyone know what is happening with K&L?

Peanut butter with cut apple slices. Work nicely...............

Hope things are progressing for you. I have a 25 Ghost with the 28" barrel. I'm finally getting good results but it has taken some work. For the speed portion I have settled on 940 with reg at 135 and 7 on the hammer. The barrel polishing has been interesting to say the least. I have...

I will give it a try.

Any words of advice? My pump went from refills in the 20 minute to over an hour. I have air blowing out the oil tank vent. I think I have enough of the parts to do rebuild but was looking to see if anyone had experience on the do's and don'ts.

Yes but a new barrel. The new barrel is a step above the stock LW. It is the first of my design of barrels for the Ghost. I will finish the slug version in a couple weeks. Then turn my attention to a 25 and 30 pellet versions.

Working on my 22 Ghost shot this...... I like the way this is working. Now to push it out to 100 and get the speed right for distance.

Thanks :)

Doing some searching tonight and not finding any good info. Can anyone lead me to the oring sizes for the Ghost breach orings? I need info on 22, 25 and 30 calibers.

When are these barrels going to be available? The competitive community is in desperate need of barrel upgrades in all calibers.

I'm running 135 on the reg and 14 on the hammer, with the stock spring. No mod it is a bit loud but mod calms the noise to very acceptable levels. I use a Impulse Air mod.

I have 2 28" setups. The 22 cal 28" is a 1:17.7 twist and the 25 cal is a 1:30 twist. I can't get much of anything to work to my target standards in the 22. The 25 cal work super great with pellets only. The 1:30 twist seems to let the pellets fight the wind better then the high twist rate...

Slugs suck! (in 28" 1:30 twist LW barrel) It is a 1;30 twist and you need the original 1:17.7 twist to have any luck with slugs. LW just doesn't seem to like slugs. My RW 177 loves a number of slugs the 13gr JSB, 15gr NSA, but can't find any slugs in RW 22 or my Ghost 28" barrel that work at...

I have the same 28" 1:30 twist barrel. The barrel was for sure the dirtiest I have ever received in a gun. Now after tons of polishing and cleaning it is shooting well. So well I'm going to give it a try at the AZ EFT next week.

Some barrels are the 1:30 you can tell if a 6B is printed on area of transfer port. I got a 1:30 25 cal its getting better but I have been polishing and whittling the rifling down. Measuring with pin gauges. I got a 22 cal but it is the 1:17 and it doesn't work for pellets. Some guys are...