Search results

While working on the trigger adjustment after installing the Rowan trigger blade, I had the stock of my R7 off a bunch of times. Despite having a Brownells screwdriver set with about 50 different tips, I managed to slightly mar up the slots of two of the three screws/bolts that hold the stock...

I can't speak for the Vevor and other brand names I can't pronounce, but the GX line will last a long time if someone is just willing to do periodic maintenance. Don't do anything to it but run it and you might have problems down the road. Read this advice by a fellow member. An important thing...

I just tried the NSA slugs out of the only PCP I have at present, the .22 Notos. It fires 18 grain pellets @ 830 fps., so the 20 grain slugs should be near that. I'm zeroed with JSB pellets at 15 yards (my backyard range) and the NSA slugs were hitting an inch higher on the target. I would have...

I just picked up a box of the NSA .22 slugs yesterday, I'll try some today or tomorrow. 20 grains sounds on the light side for a .22 slug, most of the JSB and H&N pellets I use are in the 18 grain range.

While shooting the R7 last week, I must have crossed the break-in threshold. Partway through a string of 5 shot groups, the rifle seemed even smoother and quieter than it was before. I'm at about 750 pellets. I picked up some JSB 8.44 Exacts, groups are decent, just not as tight as the 7.33...

It took a bit more moving back of the "pre travel tab" in front of the trigger, but now I have close to the same feel I had achieved with the factory trigger. The adjustment tab is leaning back at a good angle now. I ended up grinding off the slot on the brass screw that Rowan provides, then...

I did some fine tuning of the trigger today, and learned that the new shorter screw that Rowan provides can't be turned out very much, or the top/back part of the extreme setback trigger will come in contact with the screw when the trigger is pulled. Seeing that the screw is easy to turn and the...

Today I installed a Rowan Engineering trigger, an extreme set back one in black finish. The only thing that I didn't like about my R7 was how far forward in the trigger guard the trigger was, and how the long adjustment screw behind the trigger stuck down 1/2". And while I chose the R7 over an...

I had a $20 blue anodized filter from Amazon and the thing leaked badly as well. Teflon tape on the fitting threads didn't help. The GX filter is a good one, cost is just over $100.

Thankfully, full auto BB gun quality and technology is leaps and bounds better today than half a century ago.

No whitetail that I know of, just mule deer. In Montana we had both, whitetail in the river bottoms and valleys, mule deer up in the mountains.

Welcome Charlie. It is good that you can still enjoy some airgunning in the U.K. 12 ft lb. limit would be fine as my favorite new air rifle only puts out 7.5 ft.lbs. (Beeman R7, like an HW30s). Unfortunately you guys don't get the full auto capable BB guns though. I don't think I'd like the...

15 yards. My property goes back another 30 yards but the previous owner put up a 4 foot chainlink doggie fence. It is convenient to shoot off the back porch and not have to move my bench around. If I pack up targets and bench, there are a few hundred thousand acres of public land to shoot on in...

More groups today. The rifle is flawless, if only my abilities were too !

One of the groups with the AA 7.33 pellets, 4.52 head size. Several groups had most of them going into one enlarged hole, with one or two pulled slightly out by me.

Using the compressor early in the day there is less moisture in the air than when it is hot. That and the compressor running cooler in the morning is why I wouldn't use the compressor outside while it is 100 out. Of course running the compressor inside the air conditioned house will take care...

Adding a CRC plenum to my Notos allowed me to add a pressure gauge but I haven't had good luck with several Chinese gauges off Ebay. Mine are also M8, there aren't as many choices that come up in a Google search compared to some of the other sizes. My gauges froze up and the needle stuck on a...

The CS3-I will automatically shut down for 20 minutes after 30 minutes of run time for cooling. It has to remain plugged in for the cooling fans to work. For your unit to shut down after 7 minutes is unusual, but if the unit felt it was building up too much heat, it is probably a safeguard to...

GAJoe, you'll love the 250z, I had one in .25 for a while. Is this your first compressor ? As you probably already know, Bill @ Target Forge has some good videos showing maintainence and overhaul of the various GX compressors. I bought the T handle Allen set by Eklind that he recommends, they...

Assuming we all don't let our little compressors get hot, I'd rather fill to max pressure less often. It is less hassle as I have to connect and fill less. My GX CS3-I runs for around 2-3 minutes to fill my small reservoirs, I doubt it will ever get hot, it barely gets warm. Also although I use...