Search results

Anyone have the ASP Air-Superiority Products Gen 1 Picatinny Rail (that was meant for the Red Wolf/Delta Wolf) that they were willing to part with? The current version has an overhang on both ends...while Gen 1 only had the over hang on the barrel side. See picture. I checked with AoA and...

I find my Element Helix to have too tight of an eyebox…my Athlon Talos to be much more forgiving..having buyer remorse on the Helix

I got the .22 Revere and pump in Feb22...the Ghost in Sept...and I am have had zero issues with the pump..still original O-rings. I use Super Lube on the shaft about every 5th time I do a 200 to 250 pump. I check that the plastic collet at the bottom is tight prior to pumping..it seems to like...

And at least the exercise from it has purpose

IF there is any liquid water in the rifle...pointing it straight up (based on thier design) and dry firing will remove it...I have yet to see the dry fires indicate that there was liquid....The Hill drier beads color change...and I stay on top of them.....the amount of shooting I have been doing...

I fill my Ghost and Revere with a Hill hand pump that has the front end moisture removal...and to be on the safe side....every other fill or so, I point the gun straight up so that if there is any liquid water in the bottle or plenum, it will move through and out of the rifle as I dry fire it...

Fully agree, got my 177 HP Ghost, scope, .22 barrel, bipod, etc from Tom, he goes the extra mile

Interesting...something doesn't seem "right" though...if that were the case wouldn't JSB (and everyone else) make with a meplat?

I literally spent, cumulatively, well over a couple hours mounting my scope on my Revere ….making sure the rifle was perfectly level, that the scope was perfectly “square” to the rifle, and then later attaching a level to the rifle. I attached the level because my “instinctual” hold resulted in...

Learned a new word…so you push them through skirt first? And it’s the pressure on the head that flattens it? can you resize them without making the meplat? Make the pusher out of a hard wood dowel with the end contoured to match the pellet head?

I read because the smaller diameter .177 has less chance of clipping the side of a target hole esp where the close targets with their very small target holes, thus losing energy and therefore not able to trip the target paddle.…that was a 12ft-lb folks….but I would guess that also applies for...

Agree, either I need to back down the reg or use the HP hammer spring. Really windy today…was pushing the pellets left: jumbo 6+”, beasts 1/2 that… When it’s that windy…do the”shoots” get postponed?

Hello Soren, So by turning down the regulator pressure, you will use more air (lower pressure air has less energy) to achieve the same velocity, and very slightly increase the time it takes for the pellet to leave the barrel starting from when the valve opens.....but you will have more shots...

I am still “mapping” out my HP Ghost. Reg ~190 bar, MP hammer spring, .22 JSB Exact Jumbo, Heavy, MRD, & Beast: PW Min Jumbo ~860 ft/s; PW Max Beast 813 ft/s. So if I want to shoot .22 Beasts > 813 ft/s I need to go to the HP Hammer Spring. Same issue with .177, and the LP hammer spring, if i...

With all other things being equal; the ~33F plenum air vs the ~70F plenum air, having less energy will generate lower velocities… One of the advantages of having an adj plenum regulator and hammer spring preload… How much of an effect does the barrel being cold on POI?

damn....the video they posted on Youtube ...regulator looks like it is set below 140 bar...and the have the PW set at Max...but I am not sure I would go by that video...let us/me know what the regulator is set at and what pellets AoA recommends...thanks!!

You ordered the "Fady" or you ordered a .22 barrel kit for your existing ?

I did, they don't know....

I did some backyard shooting the other day...34F...halfway through my fingers were dropping pellets... What pellet are you using for this and what velocity? Do you weight sort? Head size sort? Good luck!

$3195 from AoA.... Will the custom .22 tensioned barrel be made available? its not shown on the BRK accessories page. What is the "tuning" for the .22 set up? What pellet did Fady use? Were the pellets weight and head size sorted? The Cheek riser looks like it is higher above the frame...is that...